CPU | AMD Socket AM4, support for: AMD Ryzen™ 5000 Series Processors/ AMD Ryzen™ 5000 G-Series Processors/ AMD Ryzen™ 4000 G-Series Processors/ 3rd Generation AMD Ryzen™ processors/ 2nd Generation AMD Ryzen™ processors/ 1st Generation AMD Ryzen™ processors/ 2nd Generation Ryzen™ with Radeon™ Vega Graphics processors/ 1st Generation Ryzen™ with Radeon™ Vega Graphics processors/ Athlon™ with Radeon™ Vega Graphics Processors |
Chipset | AMD B450 |
Memory | Support for DDR4 3600(O.C.)/3466(O.C.)/2933/2667/2400/2133 MHz memory modules |
2 x DDR4 DIMM sockets supporting up to 64 GB (32 GB single DIMM capacity) of system memory | |
Dual channel memory architecture | |
Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules (operate in non-ECC mode) | |
Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules | |
Support for Extreme Memory Profile (XMP) memory modules | |
Onboard Graphics | Integrated Graphics Processor: |
1 x HDMI port, supporting a maximum resolution of 4096×2160@60 Hz | |
Maximum shared memory of 16 GB | |
Audio | Realtek® Audio CODEC |
High Definition Audio | |
2/4/5.1/7.1-channel | |
LAN | Realtek® GbE LAN chip (1 Gbps/ 100 Mbps) |
Expansion Slots | CPU: |
1 x PCI Express x16 slot, supporting PCIe 3.0 and running at x16* | |
Chipset: | |
1 x PCI Express x1 slot, supporting PCIe 2.0 and running at x1 | |
Storage Interface | 1 x M.2 connector (Socket 3, M key, type 22110/2280/2260/2242 SATA and PCIe 3.0 x4/x2(Note) SSD support) |
4 x SATA 6Gb/s connectors | |
RAID 0, RAID 1, and RAID 10 support for NVMe SSD storage devices | |
RAID 0, RAID 1, and RAID 10 support for SATA storage devices | |
USB | Chipset: |
2 x USB 3.2 Gen 1 ports available through the internal USB header | |
6 x USB 2.0/1.1 ports (2 ports on the back panel, 4 ports available through the internal USB headers) | |
CPU: | |
4 x USB 3.2 Gen 1 ports on the back panel | |
Internal I/O | 1 x 24-pin ATX main power connector |
Connectors | 1 x 8-pin ATX 12V power connector |
1 x CPU fan header | |
1 x system fan header | |
1 x M.2 Socket 3 connector | |
4 x SATA 6Gb/s connectors | |
1 x front panel header | |
1 x front panel audio header | |
1 x USB 3.2 Gen 1 header | |
2 x USB 2.0/1.1 headers | |
1 x Trusted Platform Module (TPM) header (2×6 pin, for the GC-TPM2.0_S module only) | |
1 x speaker header | |
1 x Clear CMOS jumper | |
1 x chassis intrusion header | |
Back Panel Connectors | 1 x PS/2 keyboard port |
1 x PS/2 mouse port | |
1 x HDMI 2.0 port | |
4 x USB 3.2 Gen 1 ports | |
2 x USB 2.0/1.1 ports | |
1 x RJ-45 port | |
3 x audio jacks | |
I/O Controller | iTE® I/O Controller Chip |
H/W Monitoring | Voltage detection |
Temperature detection | |
Fan speed detection | |
Fan fail warning | |
Fan speed control* | |
BIOS | 1 x 128 Mbit flash |
Use of licensed AMI UEFI BIOS | |
PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0 | |
Unique Features | Support for APP Center |
@BIOS | |
EasyTune | |
Smart Backup | |
System Information Viewer | |
Support for Q-Flash | |
Support for Xpress Install | |
Bundled Software | Norton® Internet Security (OEM version) |
LAN bandwidth management software | |
Operating System | Support for Windows 11 64-bit |
Support for Windows 10 64-bit | |
Support for Windows 7 64-bit | |
Form Factor | Micro ATX Form Factor; 24.4cm x 19.5cm |
Specification may change without further notice.
After receiving the item, It has been three days already but havent tested the CPU, unfortunately, I couldn’t plug the HDMI into the CPU to connect the monitor. The HDMI socket was blocked by the back cover of the CPU, and the motherboard installation didn’t align properly with the casing holes. Please refer to the attached image. This has been quite frustrating, as it has delayed my ability to use the CPU properly. I’ll try to reposition the motherboard and explore using different HDMI cables or adapters to resolve the issue. If I can’t figure it out, I might seek help from a computer technician to get the setup right.
Greetings!
Apologies for the experience however since this is a logistic issue please reach out for support to address this since all units undergo quality testing before release. Our team install basic apps and operating system, then all ports must be accessible for us to be able to do it. Please contact our support to guide for the return process or support. Thank you
I had no problem with my order.